Viewing Condensed info mobile device app

Full website is best viewed from PC
OR
select "Request Desktop"
from you mobile device's toolbar
Your basket is empty
Categories
Shipping is calculated by size and weight in the check out section when you enter your address. Shipping starts from approx $7.50 and is in addition to the product prices shown. NOTE: You will need to create an account for payments to go through properly
Holden V8 253, 308 Alloy Rocker Covers suit early heads - Pro Street RAW shot blasted PAIR
suits HK,HT,HG,HQ,HJ,HX,HZ,WB & Commodore VB,VC,VH,VK 4.2 & 5.0 engines
$370.00
Qty
Product Description

Part# AS0215R - Raw shot blasted alloy AussieSpeed valve cover for a 8 cylinder Holden V8 engine. This rocker cover is made to clear Yella Terra roller rockers on 253 and 308 engines. It is made from sand cast aluminium, it is thick and comes with rubber grommets to take readily available aftermarket standard PCV and push in breather caps.

These AussieSpeed Holden V8 covers have a molded inner drip lip to help prevent oil leakage by holding the gasket in place, funnel style cast in breathers to stop oil splashing up at the breather and PCV, & are tall enough to clear most roller roller rockers, however in some instances with large rollers the oil baffle may need slight clearancing when fitting them up.

Large diameter valve springs up to 1.375" OD are ok. Springs over 1.375" in diameter will need relief notches machined into inside edge of valve cover.  The valve covers are approx 5 to 6mm thick in this area.

AussieSpeed V8 Holden Rocker covers are 110mm tall outside & 90mm tall on the inside. std factory tin covers are,77mm outside & 76mm inside

Want to know more
Follow our workshop projects, new products, news and events on Facebook.
 
Kustom Bitz facebook page link
Site Navigation

Kustom Bitz news

Orders placed during the Christmas new year break

by kustombitz on 19 Dec 2017
Deliveries for orders placed after the 20th dec 2017 and during the Christmas new year break will most likley be despatc...

Engine Tube custom bent up to suit your chassis

by kustombitz on 12 Dec 2017
Kustom Bitz has the parts to custom bend up a blank engine tube for you to fit in your home garage or we can set the eng...

9 inch Ford Diffs we don't skimp on cheap parts and here is why

by kustombitz on 12 Dec 2017
So by now you would have seen a wide variety of prices on Ford 9 inch diff components, housings and axles. So of the che...

Extreme 9" Diff installed in a 34 Ford chassis

by kustombitz on 12 Oct 2017
This 32 Ford chassis we used an Extreme 9 inch diff housing and one of their floater kits so we can run a 10 inch rim sa...

Hot Rod Chassis universal X member kits

by kustombitz on 12 Oct 2017
Shown here in this photo is one of our custom centre X member kit to be installed in an early 1950's pick up truck chass...

Morris J Type van with hand fabricated rear doors

by kustombitz on 17 Aug 2017
The rear doors on this little Morris J we are working on were pretty sad and the hinges were that worn I decided to star...

our exhaust hanger brackets customized and fitted to hot rod chassis

by kustombitz on 17 Aug 2017
At this years ASRF street rod nationals I saw a neat chassis on display that had our exhaust hanger brackets fitted to i...

Carburettor linkage set up custom made to suit tunnel rams, superchargers, tripples.

by kustombitz on 07 Aug 2017
Shown here is me developing a carby linkage set up for our AussieSpeed tunnel rams for a Holden 253 - 308 V8 engine. Wit...

38 Plymouth hand formed rear roll pan rust repair

by kustombitz on 07 Aug 2017
With the rear floor done and the back seat panel finished it was time to roll up a new rear tail pan on the 38 Plymouth....

38 Plymouth sedan new custom tailored boot floor and inner tail pan

by kustombitz on 12 Jul 2017
The 38 Plymouth has a Jag diff and aftermarket 32 Ford fuel tank so the old rusty floor had been removed.  To give the f...

© 2007 Kustom Bitz Pty Ltd. All rights reserved.